Toyota Corolla (E210) 2019-2025 Owners Manual / Maintenance and care / Tires / Registering ID codes
(vehicles with a tire pressure
warning system)
Toyota Corolla (E210): Registering ID codes (vehicles with a tire pressure warning system)
The tire pressure warning valve and transmitter is equipped with a unique ID code. When new tire pressure warning valves and transmitters are installed, new ID codes must be registered in the tire pressure warning computer.
- ID codes can be registered by yourself, but depending on the driving conditions and driving environment, registration may take some time to complete.
- When using a wheel set which all of the ID codes have already been registered, the wheel set can be changed in a short amount of time.
Before performing ID code registration, make sure that no wheels with tire pressure warning valve and transmitters installed are near the vehicle.
4.2-inch display
1. Park the vehicle in a safe place and turn the engine switch off, wait for approximately 20 minutes or more, and then start the engine.
The ID code registration procedure cannot be performed while the vehicle is moving.
2. Select of the multi-information
display and then
press
.
3. Press or
to select
"Vehicle Settings" and then
press and hold
.
4. Press or
to select
"TPWS setting" and then
press
.
5. Press or
to select
"Tire Set Switching" and then
press
.
6. Press or
to select
"Register New Valve / ID" and
then press
.
7. Press or
to select
"Tire Set 1" or "Tire Set 2".
Then press .
ID codes will be registered to the displayed wheel set.
If ID codes have already been registered for that wheel set, the tire pressure warning light will slowly blink 3 times, and a message indicating that change is occurring will be displayed on the multi-information display.
8. Select "OK" and then press
.
The tire pressure warning light will slowly blink 3 times and a message indicating that ID code registration is being performed will be displayed on the multi-information display.
Wheel set changing will be canceled and registration will begin.
When registration is being performed, the tire pressure warning light will blink for approximately 1 minute then illuminate and "---" will be displayed for the inflation pressure of each tire on the multi-information display.
9. Drive straight (with occasional left and right turns) at approximately 25 mph (40 km/h) or more for approximately 10 to 30 minutes.
When registration is complete, the tire pressure warning light will turn off and a message indicating that registration has been completed will be displayed on the multi-information display.
Registration may take longer than normal to complete if the vehicle speed cannot be maintained at approximately 25 mph (40 km/h) or more. If registration cannot be completed after driving for 1 hour or more, perform the registration procedure again from the beginning.
10. If the tire inflation pressure of the wheel set installed differs from that of the previous set, it will be necessary to perform the tire inflation pressure setting procedure of the tire pressure warning system.
If the specified tire inflation pressure is the same, it will not be necessary to perform the tire inflation pressure setting procedure.
7-inch display
1. Park the vehicle in a safe place and turn the engine switch off, wait for approximately 20 minutes or more, and then start the engine.
The ID code registration procedure cannot be performed while the vehicle is moving.
2. Select of the
multi-information
display and then
press
.
3. Press or
to select
"Vehicle Settings" and then
press and hold
.
4. Press or
to select
"TPWS setting" and then
press
.
5. Press or
to select
"Tire Set Switching" and then
press
.
6. Press or
to select
"Register New Valve / ID" and
then press
.
7. Press or
to select
"Tire Set 1" or "Tire Set 2".
Then press .
ID codes will be registered to the displayed wheel set.
If ID codes have already been registered for that wheel set, the tire pressure warning light will slowly blink 3 times, and a message indicating that change is occurring will be displayed on the multi-information display.
8. Select "OK" and then press
.
The tire pressure warning light will slowly blink 3 times and a message indicating that ID code registration is being performed will be displayed on the multi-information display.
Wheel set changing will be canceled and registration will begin.
When registration is being performed, the tire pressure warning light will blink for approximately 1 minute then illuminate and "---" will be displayed for the inflation pressure of each tire on the multi-information display.
9. Drive straight (with occasional left and right turns) at approximately 25 mph (40 km/h) or more for approximately 10 to 30 minutes.
When registration is complete, the tire pressure warning light will turn off and a message indicating that registration has been completed will be displayed on the multi-information display.
Registration may take longer than normal to complete if the vehicle speed cannot be maintained at approximately 25 mph (40 km/h) or more. If registration cannot be completed after driving for 1 hour or more, perform the registration procedure again from the beginning.
10. If the tire inflation pressure of the wheel set installed differs from that of the previous set, it will be necessary to perform the tire inflation pressure setting procedure of the tire pressure warning system.
If the specified tire inflation pressure is the same, it will not be necessary to perform the tire inflation pressure setting procedure.
■When registering ID codes
- Normally, ID codes registration can be completed within approximately 30 minutes.
- ID code registration is performed while driving at a vehicle speed of approximately 25 mph (40 km/h) or more.
■If ID codes are not registered easily
- In the following situations, ID code
registration may take longer than
usual to be completed or may not
be possible.
- When the vehicle has not been parked for approximately 20 minutes or more before being driven
- Vehicle is not driven at approximately 25 mph (40 km/h) or more
- Vehicle is driven on unpaved roads
- Vehicle is driven near other vehicles and system cannot recognize tire pressure warning valve and transmitters of your vehicle over those of other vehicles
- Wheel with tire pressure warning valve and transmitter installed is inside or near the vehicle
- If the vehicle is reversed during registration, all data collected until then will be cleared. Perform driving again.
- If the tire pressure warning light does not blink 3 times when starting ID code registration procedure to step 8, the procedure may not have started. Perform the procedure again from the beginning.
- If registration does not complete after driving for 1 hour or more, perform the ID code registration procedure again from the beginning.
- If the ID codes cannot be registered even when performing the above procedure, contact your Toyota dealer.
■Canceling ID code registration
To cancel ID code registration after it has been started, select "Register Valve / ID" again on the multi-information display.
If ID code registration has been canceled, the tire pressure warning light will turn off.
If the warning light does not turn off, ID code registration may not have been cancelled correctly. To cancel registration, select "Register Valve / ID" on the multi-information display.
Other materials:
Ecm/pcm processor
Dtc p0606 ecm/pcm processor
Monitor description
The ecm continuously monitors its internal circuits. This self–check insures
that the ecm is functioning properly.
If a malfunction is detected, the ecm will set the appropriate dtc and
illuminate the mil.
The two cpus, main and sub cpu i ...
Inspection procedure
Hint:
if dtc p0441 (purge flow), p0446 (vsv for ccv or vsv for pressure
switching valve), p0451, p0452
or p0453 is output with dtc p0442 or p0456 , first troubleshoot
dtc p0441, p0446, p0451, p0452 or p0453. If no malfunction is detected,
troubleshoot dtc
p0442 or p0456 next.
...
Safety Connect
*: If equipped
Safety Connect is a subscription-
based telematics
service that uses Global
Positioning System (GPS)
data and embedded cellular
technology to provide
safety and security features
to subscribers. Safety Connect
is supported by Toyota's
designated response
center, which operates 24
hour ...