Toyota Corolla (E120): Inspection procedure

1 Check p/t squib(lh) circuit(airbag sensor assy center – front seat outer belt assy lh)

  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2.  disconnect the connectors between the airbag sensor assy center and the seat belt pretensioner (lh).

    Hint

    : make sure that the connector is not damaged (the lock button is not disengaged, or the claw of the lock is not deformed or damaged). If the damage is found, replace the wire harness.

  3. release the airbag activation prevention mechanism of the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the seat belt pretensioner (lh) .
  4.  for the connector (on the seat belt pretensioner side) between the airbag sensor assy center and the seat belt pretensioner (lh), measure the resistance between pl+ and pl–.

    Ok: resistance: 1 mw or higher

2 Check air bag sensor assy center

2 Check air bag sensor assy center

Sst 09843–18040

  1. Connect the connector to the airbag sensor assy center.
  2.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  3.  turn the ignition switch to on, and wait at least for 20 seconds.
  4.  clear the dtc stored in memory .
  5.  turn the ignition switch to lock, and wait at least for 20 seconds.
  6.  turn the ignition switch to on, and wait at least for 20 seconds.
  7.  check the dtc .

    Ok: dtc b0135/73 is not output.

Hint

: codes other than code b0135/73 may be output at this time, but they are not relevant to this check.

3 Check p/t squib (lh)

3 Check p/t squib (lh)

Sst 09843–18040

  1. Turn the ignition switch to lock.
  2.  disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3.  connect the seat belt pretensioner (lh) connector.
  4.  connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5.  turn the ignition switch to on, and wait at least for 20 seconds.
  6.  clear the dtc stored in memory .
  7.  turn the ignition switch to lock, and wait at least for 20 seconds.
  8.  turn the ignition switch to on, and wait at least for 20 seconds.
  9.  check the dtc .

    Ok: dtc b0135/73 is not output.

Hint

: codes other than code b0135/73 may be output at this time, but they are not relevant to this check.

Use simulation method to check

Use simulation method to check

    Share this page:

    Other materials:

    Do-it-yourself service precautions
    If you perform maintenance by yourself, be sure to follow the correct procedure as given in these sections. Maintenance WARNING The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, obser ...

    Checking and replacing fuses
    If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Checking and replacing fuses 1. Turn the engine switch off. 2. Open the fuse box cover. Engine compartment: type A fuse box Push the tabs in and lift the lid off. E ...

    On–vehicle inspection
    Notice: ”cold” and ”hot” in these sentences express the temperature of the coils themselves. ”Cold” is from –10 c (14 f) to 50 c (122 f) and ”hot” is from 50 c (122 f) to 100 c (212 f). 1. Inspect ignition coil (with igniter) and spark test  confirm dtc. Notice: ...