Toyota Corolla (E210): Battery

Check the battery as follows.

■ Battery exterior

Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.

  1. Terminals
  2. Hold-down clamp

■Before recharging

When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, observe the following precautions before recharging:

  • If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.
  • Make sure the charger is off when connecting and disconnecting the charger cables to the battery.

■After recharging/reconnecting the battery (vehicles with a smart key system)

  • Unlocking the doors using the smart key system may not be possible immediately after reconnecting the battery. If this happens, use the wireless remote control or the mechanical key to lock/unlock the doors.
  • Start the engine with the engine switch in ACC. The engine may not start with the engine switch turned off. However, the engine will operate normally from the second attempt.
  • The engine switch mode is recorded by the vehicle. If the battery is reconnected, the vehicle will return the engine switch mode to the status it was in before the battery was disconnected. Make sure to turn off the engine before disconnecting the battery. Take extra care when connecting the battery if the engine switch mode prior to discharge is unknown.

If the system will not start even after multiple attempts, contact your Toyota dealer.

WARNING

■Chemicals in the battery

The battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery:

  • Do not cause sparks by touching the battery terminals with tools.
  • Do not smoke or light a match near the battery.
  • Avoid contact with eyes, skin and clothes.
  • Never inhale or swallow electrolyte.
  • Wear protective safety glasses when working near the battery.
  • Keep children away from the battery.

■Where to safely charge the battery

Always charge the battery in an open area. Do not charge the battery in a garage or closed room where there is insufficient ventilation.

■Emergency measures regarding electrolyte

  • If electrolyte gets in your eyes Flush your eyes with clean water for at least 15 minutes and get immediate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the nearest medical facility.
  • If electrolyte gets on your skin Wash the affected area thoroughly.

    If you feel pain or burning, get medical attention immediately.

  • If electrolyte gets on your clothes It can soak through clothing on to your skin. Immediately take off the clothing and follow the procedure above if necessary.
  • If you accidentally swallow electrolyte Drink a large quantity of water or milk. Get emergency medical attention immediately.

■When disconnecting the battery

Do not disconnect the negative (-) terminal on the body side. The disconnected negative (-) terminal may touch the positive (+) terminal, which may cause a short and result in death or serious injury.

NOTICE

■When recharging the battery

Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

    Share this page:

    Other materials:

    Refueling
    Opening the fuel tank cap Perform the following steps to open the fuel tank cap: Before refueling the vehicle ● Close all the doors and windows, and turn the engine switch off. ● Confirm the type of fuel. ■Fuel types Unleaded gasoline (Octane rating 87 [Research Octane Number ...

    Inspection
    1. Spark plug Notice: never use a wire brush for cleaning. Never attempt to adjust the electrode gap on used spark plug. Spark plug should be replaced every 192,000 km (120,000 miles). Clean the spark plugs. Air pressure: below 588 kpa (6.0 Kg/cm2, 85 psi) duration: 20 sec ...

    Check open circuit
    For the open circuit in the wire harness in fig. 1, Perform a resistance check in step (b) or a voltage check in step (c) to locate the section. Check the resistance.  Disconnect connectors a and c and measure the resistance between them. Resistance: 1 Ω or les ...